Why Learning Plumbing Basics is Vital for Bathtub Installation
Why Learning Plumbing Basics is Vital for Bathtub Installation
Blog Article
How do you actually feel about Installing A Bathtub?
Setting up a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a brand-new one is also a moderately difficult task. If the old tub is readily available, the project can relocate immediately; if you have to open up a wall to eliminate the old bathtub and also position the new bath tub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly require an assistant to vacate the old tub and also set in the new one. Ensure you have actually qualified yourself for the task and are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is better to think about using one prior to you start. Opportunities are you might need a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have actually already bought a new tub and do not need to alter the setup of your previous supply of water pipes.
Your tools and also product checklist should consist of the following:
Planning for the Installation
To start with, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile tap ports to the bottom of the two taps using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is separate the supply of water. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of getting rid of the existing faucets can be quite problematic as a result of the limited accessibility that is often the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Before going on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the called for setting. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 small factors.
The next objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the tub until the spirit level reviews degree.
To install faucets, fit all-time low of the outermost versatile tap connector to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Turn on the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill up the bathtub and also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been used a minimum of when as this will certainly resolve it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing hole in the bath/basin making sure that the washers remain in location between the tap and also the sink. Secure the tap in position with the supplier supplied backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet connectors. The previous type ought to be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall between the bath as well as the tiling, leading to complications with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger void to load, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill the bath tub with water prior to securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the tiles using water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very intrigued by Tools You Need to Install a New Bathtub and I'm hoping you liked my blog entry. I beg you take the opportunity to share this page if you appreciated it. We take joy in reading our article about How to Install a Bathtub Yourself.
Immediate relief? Contact. Report this page